Not stop draining: May 2013

Friday, May 31, 2013

What Kind Of Outlet Do I Need For A Builtin Dishwasher

The proper electrical outlet is important for the operation of a dishwasher.

The electrical connection for a dishwasher is sometimes an overlooked necessity. The proper outlet makes installing the dishwasher easier and provides trouble-free operation. The outlet specifications may be part of the home plans or part of a kitchen renovation. An outlet dedicated for the dishwasher is similar in type and capacity to other kitchen outlets.

Outlet Specifications

Home dishwashers commonly operate on 110 volts. This is the standard household current. Other considerations are the amperage of the dishwasher. Some dishwashers operate with a minimum of 15 amps while others utilize a 20-amp circuit. If the planned dishwasher operates on 15 amps consider a 20-amp circuit to allow for future expansion to a larger capacity dishwasher. The amperage of the circuit is determined by the breaker or fuse installed in the electrical utility box. The outlet for the dishwasher should be the only outlet connected to that fuse or breaker.

Ground Fault Interrupters

Ground Fault Interrupters, sometimes referred to as GFI or GFCI, provide an additional level of safety if the outlet becomes wet. The GFI trips, or disconnects the power at the outlet, before there is any electrocution danger. Building codes commonly require this kind of circuit in kitchens or bathrooms where water is present.

Outlet Placement

The simplest placement for the dishwasher outlet is under the sink. Most kitchen plans place the dishwasher next to the sink to allow easy connection to the water supply and wastewater drain lines. If the dishwasher is being placed elsewhere within the kitchen modify the outlet placement to provide for easy connection.

Installation

New dishwashers commonly arrive with the power cord not attached to the appliance. This allows the installer to trim the length of the cord to fit the situation. After cutting the cord fasten the wires to the terminals usually located at the front base of the appliance using wire nuts. Match the colors of the wire to the terminals or consult the manufacturer's instructions if non-standard wire coloring is used.

Design Kitchen Cabinets And Specs

Spacing of cabinets is important for beauty and function.

You will need to invest time in reviewing how you enjoy working in the kitchen in order to plan cabinets correctly. For example, if you use a lot of heavy cookware, you will want to create space for storing large pots and pans near the cooktop. It's important to design cabinets around appliances as well. Placement of appliances, starting with the dishwasher at the kitchen sink, will determine a lot about how both upper and lower cabinets will be spaced.

Instructions

1. Make rough sketches of how you envision cabinet placement, and finalize all design work on graph paper as you decide on actual choices.

2. Write down exact measurements of your kitchen, including closets and appliance areas already in place. Begin visualizing cabinets by starting at the sink area where the dishwasher will be placed. Plan to install two or three cabinets to the left and right of the sink overhead. Use these cabinets for dishes coming out of the dishwasher. Design doors and drawers in the lower wall areas to hold pots, pans and cooking utensils. Choose cabinets that are no less than 24 inches deep by 36 inches high.

3. Move upper cabinets higher on the wall, if necessary, to allow for at least 18 inches of clearance space between the bottom of the wall cabinets and the finished counter top along the sink area. Allow 18 inches of clearance space or more on walls with counter top workspace in other areas of the kitchen. Select fewer cabinets in a greater width across the front versus buying several narrow cabinets. Plan to use cabinets with door fronts opening to at least 24 inches, so you can stack dishes in double rows on each shelf with room to spare.

4. Review cabinet portfolios and select a grade of cabinet that will last at least 15 years. Avoid purchasing the cheapest cabinets, since they will need to be refinished after a few years or replaced. Invest in solid wood cabinets if your budget permits, but select other choices in vinyl or faux wood ranked high by consumer guides. Choose hardware and knobs that match the metal on your appliances. Select stainless steel, for example, with white cabinets if your stove has a stainless steel top.

5. Design an island near the sink area with a large base cabinet to hold large cookware pieces. Plan to place drawers in the island cabinet to make viewing pots and pans easier. Include slide-out shelves for baking sheets and oven casserole dishes, since pulling out shelves to make a selection is easier than searching through cabinet doors.

The Best Washing Machine For Clothes

The best washing machines for clothes on the market have earned an EnergyStar designation from the U.S. Department of Energy and U.S. Environmental Protection Agency. According to EnergyStar.gov, washing machines that have earned this designation use at least 37 percent less water and 50 percent less energy than regular washing machines. Some of the top brands include LG, Whirlpool, Samsung and Maytag.

LG WM2301HW

The LG WM2301HW features a water heater, LCD electronic control panel, anti-vibration system and load sensing. With 4.2 square feet of washing capacity, the LG washing machine is designed to minimize washing noise in order to prevent disruption of daily activities. The washing machine also has child lock protection, auto suds removal, four leveling legs, forced drain system, four-tray dispenser and status indicator. As of 2011, the cost of the LG WM2301HW is about $800.

Whirlpool WTW7800XW

The Whirlpool WTW7800XW is a top-loading washer with 16 automatic cleaning cycles, along with a maximum spin speed of 1,100 RPM. The washer has 5.2 cubic feet of washing capacity and five selectable water temperatures. Additional features on the EnergyStar washing machine include a quiet speed technology, noise reduction system, auto load sensing and care control temperature management. As of 2011, the price of the Whirlpool washer is $1,100.

Samsung WF448AAW

The Samsung WF448AAW is a front-loading steam washer with 4.5 cubic-feet of washing capacity. The EnergyStar washing machine has 14 different wash cycles and technology that reduces noise and vibration. The system spins at 1,300 revolutions per minute, and the steam cleaning feature helps remove stains and extend the life of clothes. The price of the washing machine is $1,400, as of 2011.

Maytag Bravos MVWB750WB

The Maytag Bravos MVWB750WB is a top-loading washer with 5.0 cubic-feet of washing capacity. In addition to earning the EnergyStar designation, the washing machine uses 70 percent less water and 66 percent less energy then traditional pre-2004 top loading washers. Along with 13 washing cycles, the washing machine has an extra rinse option, softener dispenser, temperature settings and infinite speed motor. As of 2011, the price of the Maytag washing machine is $1,000.

Clean Stove Burner Grates

After every great meal there is always the clean up to look forward to. It takes a little arm power to get those gas stoves cleaned efficiently, especially the stove burner grates. Use the suggestions that follow to help in getting your stove burner grates cleaned up and ready to cook again.

Instructions

1. Turn off both the stove top and the oven. Be sure to let them cool completely before starting to clean the burner grates.

2. Remove the burner grates from the stove top. Place them over a newspaper or trash bag and use a scraping sponge or cloth to knock loose any stuck-on food or grime buildup.

3. Soak the burner grates in a dish pan with warm soapy water overnight if necessary. If there is extreme buildup, scrub the burner grates with a paste mixture of baking soda and water. Repeat this several times as needed to remove all the grime buildup. For extreme build-up use a non abrasive kitchen cleanser such as Bar Keepers Friend or Bon Ami. Scrub the grates thoroughly, wash in soapy water, rinse well and dry completely.

4. Try different methods of cleaning the burner grates depending upon your preference. Place the burner grates in a plastic dish pan or even in a plastic trash bag. Spray the burner grates with oven cleaner and let soak overnight. Then, wash, rinse and dry as usual.

5. Put the burner grates in the dishwasher for a really quick and easy clean up. This works best if there isn't too much build up on the burner grates. It is wise to wash the burner grates in the dishwasher alone.

Ideas For Portable Corral Panels

Horses need a safe environment.

Horses have basic needs for food, water, minerals and salt, and shelter from heat and inclement weather. Horses need a safe environment where they can move around, graze and socialize. They need secure, adequate fencing in an area that's hazard free. Whether the horses are traveling to events or staying home, portable corral panels can help maintain a safe environment. A variety of materials, ranging from heavy duty steel to lighter weight aluminum and vinyl, are used to make portable corral panels. There are many different sizes and configurations of corrals, and several brands have interchangeable pieces so that the corral size can be easily adjusted. Portable corral panels can be used on a ranch or farm, a camp, or by outfitter operations working in rugged areas.

Traveling Use

Corral panels are helpful when traveling to events.

Renting stalls when traveling exposes your horse to diseases from other horses that have occupied that stall. Using portable corral panels when traveling allows your horse to move about freely in a pen so that it isn't confined in a stall. Having the horse nearby in a safe, secure environment brings a rider peace of mind. The horse will be calmer knowing someone familiar is around, which is important when competing in events or shows.

For trail rides, endurance races and camping trips, portable corrals are versatile and effectively confine the animals and provide protection from predators. Outfitters who use horses on trips into the wilderness find corral panels ideal for confining pack mules and llamas, as well as their remuda of horses.

Home Use

Corral panels can fence off hay storage areas.

Portable corral panels can be used for semi-permanent round pens for exercise and training. They can be used to hold new horses that are gradually being introduced to a new area or to isolate sick horses and those with feeding problems. The pens can serve as permanent stall dividers in the barn or be set up as temporary arenas for school rodeos, 4-H events and stock shows. Portable panels can keep horses away from a hay storage area and allow the horse to be rotated within large pastures, designating areas of selective grazing. They can be set up to shield gardens, plants or trees or serve as fencing to keep curious horses off decks and patios. Portable panels can be incorporated into permanent fencing for temporary expansion or repairs. Portable panels make extra-sturdy perimeter fencing-in areas where this reinforcement is needed to keep other large animals out.

Agricultural Use

Corral panels make temporary corrals on a round-up.

Temporary corral panels have been used at feed lots to divide pens or to make smaller, separate pens. They can be converted into permanent pen dividers and for separating cows from their calves. When cattle are rounded up on the range, portable panels are often used to make temporary holding pens. As more cattle are collected, portable panels are converted into larger corrals to hold them until they are transported to a holding yard for shipping. Sheep and pigs can also be confined in pens of portable corral panels. Super-heavy steel "Buffalo Panel 7 Bar" corral panels can be used to contain bulls and buffalo.

Clean Stainless Steel Barbeque Grill

Clean stainless steel barbecue grills after each use.

Grilling foods outdoors is relaxing and entertaining for many homeowners. However, there's nothing appetizing about grilling on a grill blackened with residue and grime. With each use, stainless steel barbecue grills accumulate grease, food residue and ashes. Cooking on dirty stainless steel grills prevents burners from working efficiently and contaminates foods with bacteria. Fortunately, the wide grid configuration on stainless steel grills allows for simple maintenance. Clean barbecue grills after each use with certain solutions and supplies.

Instructions

1. Turn off the fuel source to the grill. Put on latex gloves to protect your hands while cleaning.

2. Spread newspapers over a flat surface. Open the grill over and remove the grill racks and burner covers.

3. Place the grill racks and burner covers on the newspapers. Scrape the ash, food residue and grime from the grill racks, using a barbecue scraper.

4. Fill a plastic bucket halfway warm water. Add 1/4 cup of liquid dish detergent to the water.

5. Submerge the burner covers in the soapy water. Scrub the burner covers with a nylon scrub brush to remove grime.

6. Rinse the burner covers with warm water. Set the burner covers on clean newspapers to air-dry.

7. Spread newspapers over a slab or driveway. Spray oven cleaner on both sides of the grill racks.

8. Lay the grill rack on the newspapers. Keep the oven cleaner on the grill racks for the amount of time recommended by the cleaner manufacturer.

9. Scrape off the residue from the grill racks, using the barbecue scraper. Remove stubborn grime with a scouring pad.

10. Rinse the grill racks thoroughly with water from a garden hose. Lay the grill racks on the clean newspapers next to the burner covers to air-dry.

11. Slide out the grill's ashtray and dump the debris into a garbage can. Clean the ashtray with the soapy solution, using the nylon scrub brush.

12. Rinse the ashtray with water. Place it on the clean newspapers next to the burner covers and grill grates to air-dry.

13. Lay the burner covers and grill grates back in the grill. Slide the ashtray back into its compartment.

14. Close the grill cover. Wash all exterior surfaces of the grill with the soapy solution, using a nylon sponge.

15. Dampen a cotton cleaning rag with water. Wipe the rag over the exterior surfaces of the grill to rinse away the soapy solution.

16. Dry the exterior surfaces of the grill with a clean terry cloth.

My Garbage Disposal Leaks When The Dishwasher Is Running

A garbage disposal is a modern convenience that many people use every day. If you have a garbage disposal and a dishwasher, they are connected with a drain hose that runs between the two. If your garbage disposal leaks when you operate the dishwasher and at no other time, the problem is generally the connection of the dishwasher drain hose to the garbage disposal. This is a common problem, resulting from the hose being bumped when items under the sink are accessed.

Instructions

1. Open the cabinet door under the kitchen sink to gain access to the garbage disposal and the rest of the plumbing. Remove any items that may be in the way.

2. Locate the dishwasher drain hose. The hose is connected to the side of the garbage disposal and runs through the cabinet to the dishwasher.

3. Squeeze the end of the metal clamp that is around the connection of the dishwasher hose and the drain port on the disposal. This will loosen the clamp. If the clamp has a screw, turn the screw counterclockwise until it is loose enough to remove the hose.

4. Pull the hose off the garbage disposal. Reattach the hose and ensure it is tight against the disposal. Push the clamp to the end of the drain hose up against the disposal and tighten it.

Thursday, May 30, 2013

Ge Profile Dishwashwer Troubleshooting

GE Profile dishwashers are Energy Star--rated and offer a five-stage filtration system, a steam prewash, deep-clean cycle, more wash jets, a middle wash arm, preset detergent dispensing, nylon-coated racks, heated dry and a wide variety of wash and dry cycles. The dishwashers can be purchased online and in many appliance, home retail or department stores. Even though the Profile dishwashers come with a limited warranty to help users who need repair assistance, many problems can be fixed through some basic troubleshooting.

Instructions

1. Connect the power cord on the GE Profile dishwasher if nothing on the appliance operates. Reset or replace the circuit breaker or fuse as necessary. Shut the dishwasher door firmly before programming the dishwasher.

2. Press "Start/Reset" again if the button was accidentally pressed during a wash cycle. This will reset the dishwasher. Select a wash cycle and press "Start/Reset" once to begin.

3. Close the dishwasher door if the unit is beeping every 30 seconds. This indicates that the door was opened during operation, stopping the wash cycle. Do not press "Start/Reset," as this will only end the cycle.

4. Press "Heated Dry" five times quickly to turn off the "end of cycle" beep if you do not wish the dishwasher to beep when the wash and dry cycle is completed.

5. Reduce simultaneous use of other appliances that need hot water if the dishes are not clean enough after washing. Fill the dishwasher detergent dispenser, and avoid overfilling the dishwasher. Flush the garbage disposal if applicable.

6. Add rinse aid to the dishwasher if there is spotting on dishes. Use detergent that is fresh, and make sure you use the recommended amount.

7. Remove excess suds from the dishwasher by letting the soap evaporate and then closing the door. Press "Start/Reset" once and then again 30 seconds later to pump the leftover soap out of the unit.

8. Use a turkey baster to remove excess water from the "Smart Dispense" dispenser if there is water in the dispenser. Refill with detergent, and tighten the cap firmly.

9. Clean the interior of the tub if there are stains or odor, using ½ cup of bleach and 3 cups of warm water. Scrub the tub clean with a sponge or cloth. Run a rinse cycle to remove any bleach residue.

Fix A Dishwasher Soap Dispenser

Dishwasher Soap Dispenser

As dishwashers age, their parts may commence to clothing and gaolbreak. The leverage of new dishwasher can be pricy and hiring a reparation master can be expensive likewise. If you sustain the noesis and know-fix your dishwasher, you can get a petty more animation out of it and relieve roughly money in the summons. One portion that normally breaks on a dishwasher and can be well repaired by a do-it-yourselfer is the max dispenser.

Instructions

Cleaning the Dispenser

1. Set whether junk build-up in the goop dispenser may be causation it to outflow and not distribute aright.

2. Cleanse junk from the soap dispenser.

3. Test the soap dispenser to see if it is still leaking.

Replacing the Rubber Gasket

4. Locate the rubber gasket on the soap dispenser door. This gasket should provide a tight seal and prevent leaking when closed.

5. Examine the gasket to see if it is cracked or damaged. Replace the gasket, if this is the case.

6. Clean the gasket, if it does not appear to be cracked or damaged. Debris build-up can be the cause of a leaky dispenser.

7. Coat the gasket with Vaseline. This will moisten the gasket and help it seal properly.

8. Test the dispenser to ensure it is working properly.

Clean Electric Mixers

Electric mixers are huge time savers in the kitchen. They can fold ingredients together, whip up stiff batters and even create beautiful meringue for the tops of pies and tarts. However, if you do not clean your electric mixer properly, you may end up with old, bad food whipped in with your tasty new goodies. Not to mention that the wear and tear on the mixer can cause the machine to break before it should. Add this to my Recipe Box.

Instructions

1. Fill the mixing bowl with warm water. Do not fill it to the brim, but fill it about two-thirds full.

2. Add a few squirts of dish soap. This does not have to be a precise measurement, just use about the same as you use when you hand wash dishes.

3. Run the mixer in the warm, soapy water. As you beat the water, soap suds will form and the agitation will force any food particles off of the beaters.

4. Refill the bowl with clean warm water. Run the beaters through this water, as well, until all soap residue is gone. If necessary, you can remove them from the machine and simply hand rinse them under flowing water in the sink.

5. Wipe down the mixing machinery. Use a paper towel dampened with cleaning fluid to wipe down the handhold part of the mixer. Scrub it with the paper towel just as you would any other appliance to make sure that there are no smears or food stains on the appliance.

6. Let everything air dry for several hours. All the pieces can sit in the dish drainer while they dry.

Hook Up An Rv Waste Tank

Flush the waste tank on your RV for regular maintenance.

RVs are the preferred method for traveling across the nation and enjoying the comforts of home while at the same time camping and exploring. RVs generally have water tanks for cleaning and drinking, as well as waste tanks for travel in locations that lack a waste hookup. From time to time you will need to hook up the waste tank of your RV in order to empty the waste water tanks, as well as fill the fresh water tanks with a new supply of drinking and cleaning water.

Instructions

1. Locate the nearest campsite with full hookup service available, or somewhere where you can have access to the sewer system in order to hook up the waste tank and flush it out. Avoid simply draining the waste tank wherever you feel like it, as waste water is raw sewage. Only use appropriate facilities when hooking up the waste tank of your RV.

2. Park the RV on a flat, level area close to the sewer hookup. Ensure the holding tank drain valve is as close to the dump station opening as possible, to make sure that any spills are contained in the proper area for waste water and raw sewage. Put on a pair of latex rubber gloves and take your sewer hose attachment to the drain valve. Double check the valves for the gray (fresh water) and black water (waste) and make sure they are closed.

3. Attach the sewer hose to the adaptor on the drain outlet, and ensure that it is properly aligned by checking the stubs on the tank drain and lining them up with the tabs on the adaptor. Run the hose to the dump station hole and slide it in at least six inches.

4. Connect the garden hose to the dump station water supply and the RV and turn on the water. Open the black water tank valve and flush the waste water out of the tank. Turn off the water and close the valve when finished. Repeat the process for the gray tank if desired.

5. Add four or five gallons of water to the black water tank (flushing the toilet is the easiest way to get water into the waste water tank) as well as an appropriate amount of holding tank treatment. Follow the manufacturer's instructions for the exact amount recommended depending on the size of the waste tank for your RV.

Homemade Dish Washing Detergent

Homemade Dish Cleaning Detergent

Possibly you want to conserve your funds. Possibly you'd live in order to save the earth. Or possibly you've grown fed up with continuously drained from the cleaning utility caddy you'll need as soon as you'll need them. Largest, making your personal cleaning items is straightforward, affordable and eco-friendly. Homemade dish detergent is simple to create, for hands washing and automatic dish cleaning.

Automatic Dishwasher Powder

Dishwasher powder is created utilizing a couple of fundamental elements. Washing soda (this differs from sodium bicarbonate) will come in the laundry or dish cleaning soap aisle inside your local supermarket. Washing soda effectively will get through greasy build-on dishes. Borax, available too within the laundry aisle of the supermarket, is yet another multi-purpose cleaner. Use salt to include additional scrubbing action. Finally, citric acidity activly works to give dishes a shine and additional clean away any residue around the dishes. If you cannot find citric acidity, make use of a couple of packets of lemonade mix just use plain, unsweetened lemonade, as other tastes may dye your dishwasher another color. To have an automatic dishwasher powder, mix 1 cup each washing soda and borax with 1/2 cup each salt and citric acidity. Use one to two tablespoons of. per load of dishes.

Liquid Automatic Dishwasher Detergent

Liquid versus powder liquids is definitely an time tested debate if liquid is the detergent of preference, here is your opportunity to whip up in your own home. This recipe also requires washing soda and borax (you should use one box of washing soda and borax correspondingly for dishes, laundry along with other household cleaning projects, which makes it very reasonable). Rather than citric acidity in powder form, use fresh lemon juice for liquid detergent. Additional elements include water and castile (plant based) liquid cleaning soap. Help make your own detergent using 1/2 cup each washing soda and borax, 1/4 cup each fresh lemon juice and liquid castile cleaning soap and 1 cup warm water completely combined and saved inside a glass container (a classic mason jar is effective). Use 1/2 tablespoons of. detergent per load of dishes.

Liquid Dish Cleaning soap

Not everybody has or uses a computerized dishwasher. Should you fall under this category, you may still help make your own dish cleaning soap. Grate any bar cleaning soap, or simply buy a box of cleaning soap flakes for that cleaning soap base of the dish cleaning soap. Glycerin provides the cleaning soap a moisturizing quality helping the elements blend correctly. Lemon acrylic blends well in to the mix and provides the cleaning soap a brand new scent. Mix 1/4 cup cleaning soap flakes with 2 cups warm water before the cleaning soap dissolves, adding 1/4 cup glycerin and 1/2 teaspoon. of lemon acrylic and blend completely. Use as you would employ every other dish cleaning soap.

Troubleshoot Your Water Heater

Lacking hot water is no fun. And discolored, smelly water is just as bad. What to do?

Instructions

1. Make sure the breaker hasn't tripped, if you have an electric unit and are not getting any hot water. Press the reset button on the thermostat inside the access panel if a tripped breaker isn't the problem.

2. Suspect a buildup of sediments in the water-heater tank if the hot water is discolored or is taking a long time to replenish. If this is the case, you'll need to drain the tank completely and flush it with clean water.

3. Check the water heater's temperature settings if you have noisy plumbing. It might be too hot, and the noise may be the result of steam building up in the pipes.

4. Make sure you aren't running multiple appliances that use hot water - running the dishwasher and the washing machine will make your shower short and not so sweet.

5. Notice whether the water smells like sulfur. Sometimes bacteria that live in the water get out of control. A good dose of chlorine will usually take care of the problem. (Consult your owner's manual for the recommended dosage.)

6. Check the water temperature when the tank is full. Run hot water from the tap over a thermometer. It should be within 5 degrees of the thermostat setting. Replace the thermostat if there is a larger discrepancy.

Wednesday, May 29, 2013

Clean Rv Tank Sensors

Clean RV Tank Sensors

Your recreational vehicle (RV) is a miniature house on wheels. The vehicle contains its own water and waste-water system. The system consists of a set of plastic tanks that hold fresh water and waste water. These tanks contain sensors that transmit information to you, via an on-board display, about the level of fresh water and waste water present in the individual tanks. Over time, the sensors become dirty. This can lead to inaccurate readings and sensor failure. To clean your RV tank sensors, you don't need a harsh cleaner or to take your RV into a repair shop.

Instructions

1. Drive your RV to an RV park, campground or other area containing an RV waste station hook up.

2. Connect the tanks (gray and black) on your RV to the RV waste station connections to drain the tanks of water and waste. Use a wrench, if needed, to detach the hoses. Wear latex gloves to keep your hands from getting wet.

3. Disconnect the tank's hoses from the RV waste station after the tanks are empty. Secure the hoses to your RV.

4. Use a water hose to fill both tanks 1/3 full with clean water.

5. Add a half cup of regular dishwashing detergent to both the toilet and kitchen sink in your RV. The toilet drains into the black tank. The kitchen sink is connected to the gray tank.

Use a regular detergent, not one with lotion or other additives. These may interfere with the tanks and the attached hoses.

6. Flush the toilet and run the sink for four to five minutes to flush the soap into the tanks.

7. Drive your RV.

8. Stop at an RV drain station and drain the tanks.

9. Repeat steps at least three times to fully clean the tank sensors.

Noise Reduction For Air Conditioners

Noise Reduction

for Air Conditioners

Air conditioners can be incredibly noisy devices sometimes, and this noise can distract people in a house or neighboring apartment, making them lose sleep or hours in their workday. There are a variety of ways to block this sound or cover it up which can work for all models of air conditioners.

Sound Blanket Frame

Outdoor air conditioning units on roofs or outside rooms of houses or apartment complexes are often always running and generating a large amount of noise constantly. The best way to reduce the noise or soundproof these units is to build a simple wooden or metal frame around them and attach outdoor sound blankets to the frame. This will effectively stop most sound coming from the outdoor AC unit. Keep in mind these units need a little bit of ventilation so the frame should be built about 18 to 24 inches larger than the unit, to allow air flow but not allow noise to escape.

Window Units

Window air conditioning units can become noisy if not properly secured in the window. One way to remedy this is to put a board down below the unit and attach the unit to it firmly with brackets so that nothing on the window unit itself can rattle or vibrate. If this doesn't fix the problem, try putting a barrier around the window unit along with a blanket or a sound blanket. This will effectively reduce the noise from spreading to the other rooms of the house or apartment.

Wooden Wall

Another good option to reduce noise for outdoor air conditioning units is to simply build a wall around the unit that reflects any sound that comes from them. Build this wall out of wood so that the sound is partly absorbed and partly sent away from your home, apartment or business. Build the wall at least a foot higher the the actual air conditioning unit itself so that the sound cannot easily escape. These walls can also be built out of bricks or cinder blocks but are easier and cheaper to build simply out of wood.

Repair An Upper Rack On A Maytag Dishwasher Model Wu202

The Maytag WU202 dishwasher is a residential appliance designed for permanent installation below a kitchen counter. The dishwasher has two racks used to hold the dishes in place during the wash cycle. The racks roll in and out of the dishwasher for easy loading and unloading. The wheels on the dishwasher racks support the entire weight of the rack and may break after regular use. A broken wheel will make loading and unloading the dishwasher difficult, so it should be replaced with a new wheel as soon as possible.

Instructions

1. Extend the upper rack out of the dishwasher until the wheels reach the rack stops.

2. Use a flat screwdriver to depress the tabs on the rack stops and remove the stops.

3. Pull the dishwasher rack straight out of the dishwasher.

4. Hold the bolt on the inside of the rack using an adjustable wrench and loosen the wheel axle with the screwdriver. Repeat for each wheel that you would like to remove.

5. Place a new wheel from a wheel kit on the axle and place the bell-shaped metal washer on the axle, resting against the wheel.

6. Insert the axle into the axle hole on the rack and place the small lock-washer, large rubber washer and small rubber washer onto the axle.

7. Thread the hex-nut from the wheel kit onto the end of the axle and tighten using the adjustable wrench and screwdriver. Repeat for each wheel that you would like to replace.

8. Slide the rack back into the slide arms and push it into the dishwasher.

9. Snap the rack stops back into place.

Sublease Checklist

Use a sublease checklist before moving into an apartment you're subletting.

A sublease or sublet is an agreement where one person moves into an apartment while another person's name remains on the lease. The new tenant agrees to follow the same rules as the original tenant and pays rent and any other bills associated with the property. This usually occurs when the original tenant moves out of town for a job or leaves for another reason. Using a sublease checklist to document the condition of the apartment protects both the original tenant and the new tenant.

Flooring/Walls

On or before your move-in date, do a walk-through inspection with the original tenant. Complete a full inspection of the property, including the floors and walls in each room. Make note of any problems or damage to the walls and flooring. Look for holes in the walls, damaged drywall, stains on the carpet and holes in the carpet.

Appliances

Inspect any appliances in the property, including the dishwasher, stove, oven, refrigerator, washer and dryer. It's especially important to inspect any appliances that come with the apartment, as you can be charged for any damages made to those items. Check to ensure the appliances are working properly and make note of any missing pieces, dents and scratches.

Individual Rooms

Pay attention to specific damage in each room. Check the counter and cabinets in the kitchen, looking for holes in the wood, stains on the counter and any other problems. In the bathroom, focus on the fixtures, such as the faucet and shower head. You also need to pay attention to any specific built-ins found in the apartment, including bookshelves that are broken or have missing shelves.

Other Items

After completing a thorough inspection of the property, do another walk-through and focus on the items that others might ignore. Raise the windows and ensure each one works properly. Then check the screens and note any missing screens or screens with holes. Look at the fire extinguisher, which should be up to date and make sure the smoke detectors work. Inspect any ceiling fans in the property, as well as the central air conditioning and make sure that all lights in the property work. End your inspection by making note of any problems found with the doors and the locks.

Remove The Filter In A Frigidaire Selfcleaning Dishwasher

Frigidaire self-cleaning dishwashers have a filter that removes food residue from dishes that might otherwise block proper cleaning or draining. Some dishwasher models have a glass trap within a filter to catch any pits, broken glass, bones or straws that fall into the bottom of the tub. Other models have a cylinder-shaped filter in the bottom of the tub.

Instructions

Glass Trap Models

1. Locate the filter under the bottom spray arm.

2. Pull out the glass trap by the handle and empty the contents.

3. Rinse the trap with water to remove any excess debris or shards.

4. Slide the glass trap back into position.

Cylinder Filter Models

5. Disconnect power to the Frigidaire dishwasher.

6. Pull the bottom rack out of the dishwasher. Turn the cylinder-shaped filter under the spray arm counterclockwise and lift out.

7. Empty out the filter and rinse it with water.

8. Unscrew the bottom spray arm and remove the spray arm from the dishwasher.

9. Lift out the filter housing. Rinse the filter housing with water.

10. Reverse the above steps to replace the filter housing, spray arm and cylinder filter.

Get Free Appliances

Check ads for items being given away.

The next time your coffeemaker burns out or your washing machine goes on the fritz, check out some options to replace the items for free before you head out to the store. Frequently people who are moving or remodeling will give away used appliances. In most cases, they will expect you to pick up the item and they'll want you to do so as soon as possible.

Instructions

1. Check your local newspaper for advertisements for free items. You'll mostly find items for sale, but occasionally you'll find items that the owner is willing to give away.

2. Check Craigslist. Craigslist offers a myriad of ads for your particular locale, making pickup a breeze. Simply search for the item you need and see if anything strikes your fancy. Again, many of the ads will be for items for sale, but you will find a few free items, too. Check back frequently because new listings are posted all the time.

3. Check Freecycle.org. This is a nonprofit organization dedicated to preventing perfectly useful goods from winding up in a landfill. The best part about this site is that everything listed is absolutely free. You are responsible for pickup. The service requires you to be a member, but membership is free. Simply type in your city to find a group near you to see local postings.

Tuesday, May 28, 2013

My Admiral Dishwasher Is Not Cleaning Dishes

A dishwasher not only lightens your washing load in the kitchen but also uses up to one-sixth less water than traditional handwashing. Sometimes your Admiral dishwasher doesn't effectively clean all your dishes, and you end up re-washing them to remove food or film, especially on glassware. Combat the problem with your dishwasher to prevent washing your dishes twice.

Heat

The water in your dishwasher needs to be a minimum of 120 degrees Fahrenheit to properly clean the dishes. Most of the energy your dishwasher uses is to heat the water. Turn your water heater up to eliminate the need for your dishwasher to heat it, and run the hot water from your faucet for a minute before you begin the cycle.

Minerals

Most water contains minerals such as calcium and magnesium that create a film on dishes, specifically glassware. Consumer Reports completed an investigation and noted that dishes washed in hard water 20 times, simulating a month's worth of dishwashing, developed a white film due to constant exposure to minerals and the inability of dishwashing detergents to combat them.

Prewashing Dishes

Don't prewash your dishes before you put them in the dishwasher. Scrape the food off into the garbage disposal or a garbage can, then place the dishes in the dishwasher. Mike Edwards from BSH Home Appliances reports that dishwashers need food on the dishes to work effectively, and if they don't have food on them, the detergent will create a white film on your dishes. Don't overfill the detergent dispenser either, and use a powdered detergent instead of liquid or gel.

Vinegar

Vinegar is effective at removing buildup on your dishes and preventing buildup from forming inside your Admiral dishwasher or in the pipes. Run a cycle once a month -- and more often if you do dishes frequently -- with vinegar in the detergent dispenser. You can also place a bowl filled with vinegar in the bottom rack of the dishwasher when you run the cycle as an alternative to using the dispenser.

Frigidaire Dishwasher Door Flies Open When Running

Frigidaire dishwashers use an electronic latching organization holding the dishwasher unopen patch it's track. Withal, sometimes a threshold leap breaks, causation the dishwasher to fly clear midcycle. This is life-threatening. Don't run your dishwasher until you fix the trouble. You can supersede doorway springs yourself and leverage the parts on-line.

Whirlpool Washing Machine Repair & Troubleshooting

A washing machine that doesn't work usually has one of two problems.

Whirlpool is a brand name that many consumers have trusted over the years. Even though they make a very good washing machine, no washing machine is above the need for occasional maintenance and repair. When your Whirlpool washing machine isn't working properly, there are two ways to diagnose the problem. If the washing machine isn't spinning, the problem probably resides in the washing machine belt. If the washing machine isn't draining, then there is probably a clog in the drain tube.

Instructions

Machine Won't Spin

1. Unplug your Whirlpool washing machine from the wall. Pull the washing machine out so you can have access to the back of the unit. Use a screwdriver to remove the screws that hold the control panel on top of the unit.

2. Lift the top panel off of the unit and set it aside. Remove the screws on the bottom of the unit so you can take the side and front panels off of the washing machine.

3. Locate the washing machine belt. This will be in the back of the unit under the washer basket. If the belt has snapped, it will probably be on the floor. If the belt hasn't snapped, but has come off of the motor, it might just be hanging off of the motor.

4. Stretch the belt until you can get it off of the motor. Check the belt for any tears or cracks and replace it if necessary.

5. Reattach the belt or replace the belt with your new one. Replace all of the panels and the screws. Reattach the control panel to the top of the unit. Plug the unit in and test it to make sure the washer is spinning.

Machine Won't Drain

6. Unplug your Whirlpool washer from the wall. Rock the unit backward and place a towel or a piece of carpet under the unit. This will help so you don't scratch your floor when you move the unit.

7. Move the unit outside. Use a screwdriver to remove the screws that hold the control panel on top of the unit.

8. Lift the top panel off of the unit and set it aside. Remove the screws on the bottom of the unit so you can take the side and front panels off of the washing machine.

9. Locate the drain tube. This will be on the left-hand side of the unit coming off of the basket. Unplug it from the unit and allow the water to drain from the basket. Pull the clog from the drain tube.

10. Reattach the drain tube to the unit. Replace all of the panels and the screws. Reattach the control panel to the top of the unit. Plug the unit in and test it to make sure the washer is spinning.

What Is The Size Of A Standard Kitchen Room

The average kitchen size is going to vary depending on the dwelling type.

A kitchen remodel is among the most profitable investments a homeowner can make. When done properly, the space should be both aesthetically appealing and functional. The first step to any kitchen remodeling project is knowing the dimensions you'll be working with. These measurements will help you make appropriate decisions when it comes to cabinet and appliance sizes. Purchasing these pieces in the correct proportions will leave more space for easy movement when entertaining and preparing food.

Layout

During the layout phase of a remodel, knowing precise dimensions aren't necessary. A rough sketch of the layout should include placement of cabinets, appliances and fixtures. This type of sketch is used primarily to do cost estimates for materials and cabinets and deciding on a basic layout. Use rough dimensions and draw up a few design options, this will help determine which layout is best for the space without a great deal of effort.

Standard Room Measurements

The actual size of the space is going to vary greatly depending on the size of the home. According to dimensionsguide.com, the average dimensions of a kitchen give approximately 300 square feet of space. It is important to remember that there is no standard square footage, and apartments and townhomes will generally be smaller than single family homes. There are a few measurements will be more or less standard throughout all construction projects. Average room height, according to runmyhouse.com, is 96 inches. Door widths are normally 36 inches, and door heights are normally 84 inches. These measurements are a good starting point for a kitchen remodel, and specific guides for measuring the width and length of the space are available online. When drawing out the layout with these specific measurements, it is important to label interior and exterior walls and the locations of electrical outlets, windows, doors and soffits, if applicable.

Basic Appliance Dimensions

For the most part, kitchen appliances, including the refrigerator, range and dishwasher, have fairly standard measurements no matter the manufacturer. Additionally, most major manufacturers will produce products in a smaller and larger size ideal for different size spaces. A standard dishwasher is between 24 and 30 inches wide, 25 inches deep and 34 inches tall. Compact options for apartments or townhomes are available as narrow as 18 inches wide, 22 1/2 inches deep and 32 1/2 inches in height. Both electric and gas ranges come in a standard 30-inch width, with a wide variety of depths and heights. More compact options are as narrow as 20 inches wide, and larger sizes are as wide as 40 inches. The size of a refrigerator is going to depend largely on the style -- there are side-by-side models, or those with a top- or bottom-mounted freezer. Side-by-side styles are standard at 32 inches wide and 66 inches tall, while bottom freezer designs are about 30 inches wide and 66 or 67 inches tall. Top freezer models are approximately 28 inches wide and 61 1/2 inches tall.

Movement Dimensions

Designing a kitchen that provides for comfortable movement is an essential element in a successful remodel. A kitchen that is well set up will not only have a layout that is efficient for work, but also allows for movement of the cook and guests. The rule of thumb is to create walkways that are at least 24 inches wide. The refrigerator door should have at least 36 inches of uninterrupted space. This measurement takes into account the open door and provides space for someone to stand in front of the fridge. A kitchen island should have at least a 24-inch clearance on all sides. This will allow space for work, movement and eating in, if desired. Oven and dishwasher doors should have at least 48 inches in front to allow the doors to fully open.

My Bosch Dishwasher Top Leds Won'T Light Up

Many Bosch dishwashers use LEDs on the control panel.

Your Bosch dishwasher features a control panel with several LED lights which indicate the current status and set-up of the appliance. LED lights come on when the dishwasher is cleaning, when you are programming a wash cycle and when the appliance is in standby mode. The LED lights won't come on when the appliance is switched off or not receiving power. Fixing the LED lights will mean restoring power to the dishwasher.

Instructions

1. Test the dishwasher's electrical outlet with a lamp; the outlet isn't receiving electricity if the bulb doesn't light. Check the power switch for the dishwasher, if fitted, within the electrical outlet or on the wall behind your kitchen counter.

2. Replace any blown fuses or tripped breakers in your home if the outlet is switched on but not supplying electricity. You might notice other appliances on the same circuit stop working when a fuse blows or a breaker trips.

3. Hit the "On/Off" button on the dishwasher's control panel. Many Bosch dishwashers can be turned off via the power button without switching off the electrical outlet.

4. Unlock the dishwasher's control panel. Some Bosch dishwashers come with a child lock that prevents kids from starting the dishwasher by accident. Cancel the lock by downing the "Lock" or padlock icon button for a few seconds.

Deodorize Smelly Plastic Food Containers

Plastic has become a daily part of life. You dispose of garbage in plastic bags, buy children plastic toys, drink out of plastic mugs and store food in plastic containers. Because plastic containers are made from polypropylene, they are porous. Food odors can stay in the plastic if the food is stored for a long period of time. If you hate the idea of throwing out the containers when they get smelly, there are ways to clean them and eliminate the smell. Ideal cleaning agents are right in your kitchen, so look around you and you will find what you need to deodorize smelly plastic food containers.

Instructions

1. Get out the automatic dishwasher detergent. Fill the container with hot water and one to two teaspoons of automatic dishwasher detergent. Shake it up to get the detergent sudsy and then let it sit overnight. In the morning, rinse out the container. If the smell is still there, add baking soda and warm water and soak again. This should finish the job and you will have a pleasant smelling plastic container.

2. Reach for the baking soda. Make a paste out of baking soda and warm water. Coat the entire plastic container on the inside, cover and let it sit for a day or overnight. Thoroughly rinse. Try sprinkling the baking soda into the container, shake it around, cover and let it sit for a day. Rinse thoroughly.

3. Grab the vinegar. Fill the container with warm water and 1/4 cup of vinegar. dd a few drops of dish detergent and shake. Set aside for a few hours, then rinse completely. Out of vinegar? Try lemon juice.

4. Pull out the vanilla. Rub the container with vanilla and let it sit overnight. Or, put the vanilla in warm water, shake, and let it sit out overnight. Wash thoroughly in the morning.

5. Open up that bag of coffee beans. Coffee beans or used coffee grounds are great deodorizers. In fact, dry coffee grounds left in the refrigerator work like baking soda. The grounds will soak up odors. Either place a few coffee beans in the container or place dried coffee grounds in the container. Cover and let set for a day or overnight. The beans or grounds should take care of the odors. Dry the coffee grounds by spreading them out on a cookie sheet.

6. Plastic containers are a convenient way to store food, but they do collect odors. Before throwing them away, try out the deodorizing ingredients right in your kitchen. You may save some money.

Break Into A Safe

If you lose the combination to your safe, you may consider breaking into it. Caper films allow you to observe burglars breaking into a safe. Though the believability of these safe cracking methods are often doubted. Use these tips to break into your safe or to prevent your safe from being broken into by burglars looking to make a profit.

Instructions

1. Locate information to determine exactly what type of safe you own. Breaking into a safe depends on the brand and the entry resistant safeguards. Organizations such as "Underwriters Laboratories" conduct tests on safes and rates them. The more time a safe takes to open the more resistant it is to burglars.

2. Get the safe's blueprints. All safes are different. Made of several layers of material safes are designed to offer protection when someone attempts to use force to gain entry. Analyze a safe's weak points and construction to find the easiest route of entry.

3. Pick the lock. Picking a lock allows you to retrieve the contents from a safe without doing any damage to it. Tools can be bought from the manufacture or ordinary hand tools can be used on a lower end safe.

4. Use forced entry. To break into a safe, drilling is the most popular method of forced entry. Since safes are made from resistant materials such a concrete and metal this method uses a lot of physical force. Punching, torching and other methods of forced entry can be used with various results. Engineering drawings found online reveal the weaker areas where force can be applied.

5. Put in the right combination. Open the safe by dialing every possible number combination. Track the numbers you have already tried, this process could take days. Auto dial machines that dial every possible combination of numbers may be available. These machines only work with a specific type of lock and must dial through thousands of combinations.

Monday, May 27, 2013

Get Rid Of Foggy Glasses With Homemade Dishwasher Soap

Washing dishes in a dishwasher can lead to foggy glasses.

When first purchased, drinking glasses are shiny and can easily be seen through. However, after washing the glasses in a dishwasher, after time, many turn foggy in appearance. This can be due to hard water. With a few simple steps, the foggy appearance or film can be removed using homemade dishwashing detergent. This process may need to be repeated a few times throughout the year if your glasses are regularly exposed to hard water.

Instructions

1. Place equal parts washing soda and borax into a food processor.

2. Use the lowest setting to mix the ingredients and turn the mixture into a powder. For use in a dishwasher, use 1 to 2 tablespoons per load.

3. Mix one part detergent and two parts hot water in a large bowl. Be sure the detergent dissolves in the water. Place the foggy glass in the water. Allow it to sit for at least an hour. Remove the glass and wipe it dry with a clean towel. Repeat the process if the glass is still foggy.

Clean A Granite Counter Top

Clean a Granite Counter

It's reliable advice that granite counter tops cost a bit more than laminate. The main difference in cost reflects in the standard and sturdiness. But despite the fact that these visually preferred counters provide sturdiness, everybody get their weak points --- proper maintenance and care is important. Fortunately, good care is both super easy and affordable. It is a small cost to pay for that keeps granite counters searching as elegant because they were meant to.

Instructions

1. Mix 2 teaspoons of dish cleaning soap with &#xBC cup of alcohol inside a bottle of spray and fill the bottle with water.

2. Spray the counters using the solution and wipe up having a soft, flannel.

3. Cleanup spills immediately on granite counters. Soda, coffee, and tomato-based items can etch granite. Make use of a soft, clean, moist cloth to remove spills.

4. Remove stains on dark granite surfaces by mixing flour and peroxide right into a thick paste and using it towards the stain. Cover the paste with plastic wrap, tape lower the perimeters and let it sit overnight. Each morning make use of a plastic or rubber spatula and scrape away the paste. Wipe the region clean having a soft, moist cloth.

5. Remove stains on light colored granite by mixing liquid dish cleaning soap and flour right into a thick paste, using it towards the stain and departing it overnight. Make sure to pay for it with plastic wrap, as with Step Four, and tape lower the perimeters to help keep the moisture in. Each morning, scrape away the paste having a plastic or rubber utensil and wipe the area clean with a moist cloth.

Find The Model Number On An Electric Stove

Finding your stove's model number can be tricky.

Finding the model number on your electric stove can be more challenging than expected. Because of the required sterile cooking appliance specifications, model numbers are most often not found in easily spotted places on the stove top or in the oven, but in unseen places where the labels cannot accumulate dangerous bacteria and contaminate food. When locating your range's model number be prepared to take pieces of the range apart.

Instructions

1. Locate the fuse cover on the top, back portion of your range. Carefully lift the cover off the fuse compartment and look on the cover's underside for the model number. Replace the cover in the same orientation on top of the fuse compartment.

2. Pull each of the burners out of their sockets and look on the underside of each burner dish. If you still do not see the model number, carefully lift the stove top from the edge and glance underneath in each corner. Replace the stove top and all of the burner dishes and their respective burners.

3. Pull open your oven door and look at the upper left corner for the model number. Few ranges place the model number labels here, but it is wise to check.

4. Open the bottom drawer of the range. Check all four corners on the range, then check the four inside corners of the drawer door.

5. Slowly pull the range away from the wall and far enough that you can see down each side. Check both the right and left sides toward the rear and bottom of the range. Look at the top of the range behind the fuse compartment on the backside.

Treat Ticks And Mites On Pet Snakes

Mites and ticks cause serious problems in captive reptiles. If left untreated, they consume enough blood to cause a life-threatening case of anemia. Mites and ticks transmit pathogens such as roundworms and bacteria that cause pneumonia, mouth rot and inclusion body disease, a fatal viral infection of snakes. Learn prevent, detect and treat mites and ticks to keep your snake healthy.

Instructions

Prevent Mites

1. Wash the snake enclosure weekly with hot, soapy water. Ventilate the enclosure and avoid warm, damp conditions. Use commercial mite preventatives such as Provent-A-Mite, which is available at the Pro Products website.

2. Quarantine new reptiles for a month and observe for mites and ticks. Have your new snake examined by a veterinarian and all snakes examined yearly.

3. Avoid particulate floor coverings like gravel and corncob material, which provide hiding places for mites and their eggs.

4. Use a magnifying glass to check for mites, which appear as black or red dots in skin folds, along the lower jaw and around the eyes and cloaca. Check for dull skin, bad sheds and pitted or crusty scales.

5. Watch for lethargy and appetite loss. Note if the snake acts agitated, continually moves around and rubs against the cage furniture. Look for dead mites in the water bowl.

6. Lay the snake on a large sheet of white paper. Flick the area around the scales near the head, neck and cloaca with a small brush. Check the paper for mites.

7. Put the snake in a white pillowcase overnight. Check for mites at the bottom of the pillowcase in the morning.

Quarantine the Infested Snake

8. Put the snake in a separate tank, without cracks, that is easy to clean.

9. Use furnishings made of cardboard boxes, and line the bottom with paper towels.

10. Put a line of petroleum jelly around the tank rim to prevent the escape of mites.

11. Place the tank in a shallow tray of water to create a mite barrier.

Treat with Water Bath

12. Soak snake in lukewarm water for 30 minutes to drown mites. Cover the snake's back, but not its head so it can breathe.

13. Wipe snake dry and place it in the enclosure with paper towels or plain newspaper.

14. Repeat until you don't see dead mites in the bath water.

Treat with Oil Rub

15. Wear old clothes because the oil will stain.

16. Rub a small amount of mineral or vegetable oil on your snake to smother the mites.

17.Place the snake on paper towels overnight.

18. Soak in lukewarm water the next morning and wipe the snake dry.

19. Repeat until you don't see dead mites in the bath water.

Use Commercial Products or Medications

20. Consult with your veterinarian before you use an insecticide or pesticide on your snake.

21. Read and follow the directions on the bottle carefully. Observe your snake for any adverse reactions.

22. Check with your veterinarian to treat the snake with Ivermectin, as it can be highly effective, but fatal if not administered properly.

23. See if your veterinarian recommends Fipronil, an active ingredient in flea prevention products. Use to spot treat mites in hard-to-reach areas. Rinse with water after treatment to avoid intoxication.

Treat the Cage and Surrounding Area

24. Remove everything from the cage and throw away everything you can. Clean cage furnishings in hot, soapy water or a solution of 3 oz. of bleach to 1 qt. of water. Rinse or put in the dishwasher.

25. Bake wooden cage accessories at 200 degrees F for two hours. Check to ensure they don't burn.

Place cage furnishings in boiling water for 30 minutes or in the freezer for 24 hours.

Take cage outside and clean with lice shampoo to kill mites. Pay attention to cracks and crevices. Rinse and air out to diffuse the fumes. Dry in direct sunlight to kill remaining mites.

Use paper towels or blank newspaper for several days to see any new mites or their eggs.

Disinfect hardwood floors, drapes and carpets near the cage. Mites travel up to 15 feet per day.

Repeat this process every three days until mites aren't present on your snake.

Treating for Ticks

Check for ticks regularly with a magnifying glass. Look under the scales, in the nostrils and any place they can hide.

Look for abnormal skin shedding and wounds.

Grab the tick with tweezers by the head where it's attached to the skin and pull firmly and directly out without twisting.

Place the tick in a jar of alcohol to kill it.

Disinfect the wound and apply antibiotic ointment.

Friday, May 31, 2013

Outlet Specifications

Ground Fault Interrupters

Outlet Placement

Installation

Related posts

Instructions

Related posts

LG WM2301HW

Whirlpool WTW7800XW

Samsung WF448AAW

Maytag Bravos MVWB750WB

Related posts

Instructions

Related posts

Traveling Use

Home Use

Agricultural Use

Related posts

Instructions

Related posts

Instructions

Related posts

Thursday, May 30, 2013

Instructions

Related posts

Instructions

Cleaning the Dispenser

Replacing the Rubber Gasket

Related posts

Instructions

Related posts

Instructions

Related posts

Automatic Dishwasher Powder

Liquid Automatic Dishwasher Detergent

Liquid Dish Cleaning soap

Related posts

Instructions

Related posts

Wednesday, May 29, 2013

Instructions

Related posts

Sound Blanket Frame

Window Units

Wooden Wall

Related posts

Instructions

Related posts

Flooring/Walls

Appliances

Individual Rooms

Other Items

Related posts

Instructions

Glass Trap Models

Cylinder Filter Models

Related posts

Instructions

Related posts

Tuesday, May 28, 2013

Heat

Minerals

Prewashing Dishes

Vinegar

Related posts

Related posts

Instructions

Machine Won't Spin

Machine Won't Drain

Related posts

Layout

Standard Room Measurements

Basic Appliance Dimensions

Movement Dimensions

Related posts

Instructions

Related posts

Instructions

Related posts